For aircraft makers and integrators
A solid oxide fuel cell power module for UAV manufacturers
NEOVIUX is developing a 3D-printed ceramic solid oxide fuel cell (SOFC) power module for unmanned aircraft that need more endurance than a battery gives, less noise than an engine, and fuel that is easy to source. This page sets out what the module is, how it compares, and where the evidence stands.
Why look beyond the battery
For many small and medium UAVs the battery sets the endurance ceiling: the pack is a large share of take-off mass, and range grows only as fast as cell chemistry improves. A combustion engine flies longer, but adds noise, vibration, an acoustic and thermal signature, and engine maintenance. A hydrogen PEM fuel cell is quiet, but needs a hydrogen supply chain, and water management in cold air is a known difficulty.
A solid oxide fuel cell takes a different route. It converts fuel to electricity electrochemically instead of burning it, runs hot inside (above 600 °C), and can use fuels that are already easy to handle: ethanol, methane, propane and LPG. The price of that route is a warm-up period, which is why the design target is a start-up under 20 minutes.
What the NEOVIUX module is
The module is a hybrid unit: a printed SOFC stack, a multi-fuel tank and a battery in one housing, so the airframe sees fuel going in and power coming out. The cell at its centre is a single, continuous ceramic gyroid lattice, printed in one piece, instead of a flat stack of metal plates, glass seals and heavy clamping.
| Parameter | Target |
|---|---|
| Power, first prototype | 500–600 W at 24–32 V |
| Long-run aim | Scale up to 1.5 kW |
| Fuels | Ethanol, methane, propane, LPG (JP-8 and Jet-A as a longer-term target) |
| Operating range | −45 to +50 °C |
| Start-up time | < 20 min |
| Efficiency | ≥ 50–60% |
| Intended aircraft class | 15–35 kg fixed-wing and VTOL UAVs |
What is already measured
The cell physics is public and peer-reviewed. The gyroid cell was developed at DTU Energy, Technical University of Denmark, and published in Nature Energy (2025). At cell level:
- More than 1 W/g specific power and more than 3 W/cm³ volumetric power density; planar and tubular stacks sit below 0.2 W/g and 1 W/cm³.
- Six times the active area per gram, and four times per unit volume, against conventional SOFC stacks.
- Over 75% of a conventional stack is interconnects and seals. The monolithic lattice removes that weight.
- Hundreds of hours of steady operation, with degradation comparable to cells of the same materials, stable through thermal cycling.
The module itself is at TRL 3–4. The 14–22 hour flight time is modelled, not measured at module level, and the module figures above are targets. We would rather say so plainly than let a datasheet imply otherwise.
How it compares with batteries, engines and PEM
| NEOVIUX SOFC | IC engines | PEM fuel cell | Conventional SOFC | |
|---|---|---|---|---|
| Flight time | 14–22 h (modelled) | 20+ h | >10 h | 8+ h |
| Cold, down to −45 °C | Target (to be tested) | Works | Open-cathode dries out | No flight data |
| Efficiency | ≥ 50–60% | ~20–30% | ~40–60% | ~40–60% |
| Start-up time | < 20 min | Seconds | Minutes | ≥ 30 min |
| Fuel flexibility | High | Petrol or heavy fuel | H₂ only | High |
| Emissions | Low, fuel-dependent | High CO₂, NOₓ | Very low | Low, fuel-dependent |
| Power packing density | Very high | Medium | Low | High |
Read the table as positioning, not a verdict. Engines start in seconds and PEM stacks start in minutes; an SOFC takes longer. In exchange the SOFC offers fuel flexibility, high power density and, by design, tolerance of cold. See drone power for cold-weather operations for that argument in full.
Where it fits in an aircraft
The module suits aircraft that spend most of their flight in steady cruise: fixed-wing UAVs and fixed-wing VTOL aircraft on long patrol, survey or resupply legs. Take-off, climb and hover draw power peaks; in a hybrid module a battery sits alongside the stack for those, while the stack supplies the cruise load. A longer flight on the same airframe, or the same flight with more payload, is the point.
We brief a small number of aircraft makers, mission operators and research teams. The technical brief follows the first conversation, and we review each request for the technical sheet.
Frequently asked questions
- What is a solid oxide fuel cell (SOFC)?
- A solid oxide fuel cell converts fuel and air into electricity at high temperature, above 600 °C, across a solid ceramic electrolyte. There is no combustion. Because it runs hot it can use hydrocarbon fuels such as ethanol, methane, propane and LPG directly, which a low-temperature PEM fuel cell cannot.
- SOFC or PEM fuel cell for a drone?
- PEM stacks run cool and usually need hydrogen; they start in minutes. An SOFC runs hot, takes longer to start (our target is under 20 minutes), and can use fuels that are already easy to handle. For long cruise legs, fuel flexibility and cold-weather tolerance favour the SOFC; for fast starts and hydrogen-ready fleets, PEM remains the simpler choice.
- Which fuels does the NEOVIUX module use?
- It is designed for ethanol, methane, propane and LPG, with JP-8 and Jet-A as a longer-term target, so field use does not have to wait for a dedicated hydrogen supply chain.
- How much power does it deliver?
- The first prototype targets 500–600 W at 24–32 V, with a long-run aim of scaling up to 1.5 kW. These are development targets as of September 2026, not measured module results.
- Is the module available to buy?
- Not yet. The cell results are published and peer-reviewed; the module is in development at TRL 3–4. We brief a small number of aircraft makers, operators and research teams, and the technical sheet is available on request.
- Why is the cell 3D-printed in a gyroid shape?
- A gyroid is a triply periodic lattice. Printed as one self-supporting ceramic monolith, it packs far more reaction area into each gram and removes the metal interconnects, glass seals and clamping that make planar stacks heavy.
Brief us on your aircraft
Aircraft makers, operators and research teams can request the technical sheet. We review each request and answer it personally.
